Need Front Clip Painted.....

[Feedman]

I am in need of a good paint job...matched as close as possible....EBP.

The front clip (urethane) is all dinged up and whoever painted it last did a reall crappy job b/c the clear coat pealed off with some of the paint...

So...if anyone could post some info on where I can take it locally, that does a good job for a reasonable price...I would be interested.

Thanks all... 8)

[Don juan futon]

I told ya man! Ullman's body shop

[Feedman]

I told ya man! Ullman's body shop

I forgot...I was hoping you would post up..lol.

Where is that exaclty?

I may run over there on Wednesday after work or something....


8)

[Don juan futon]

Go down that road behind movie gallery towards colegate. Then right before colegate, it's on the left. There's a furniture store right on the corner, but it's the buliding RIGHT before the furniture place. It doesn't look like much, but trust me, they do good work.

[Feedman]

Go down that road behind movie gallery towards colegate. Then right before colegate, it's on the left. There's a furniture store right on the corner, but it's the buliding RIGHT before the furniture place. It doesn't look like much, but trust me, they do good work.

A # or there hrs?

B/c I won't be able to get there through the week, until 5:00 or so....??

Unless they are open later or on the weekends.... 8)

[Don juan futon]

Go down that road behind movie gallery towards colegate. Then right before colegate, it's on the left. There's a furniture store right on the corner, but it's the buliding RIGHT before the furniture place. It doesn't look like much, but trust me, they do good work.

A # or there hrs?

B/c I won't be able to get there through the week, until 5:00 or so....??

Unless they are open later or on the weekends.... 8)

NOt sure of either off the top of my head. It's in the phone book though.

[Davis Silver Sti]

Adam, if you need another option, you can call my brother in law who is a paint and body specialist.
He's really good.

SE Customs 984-0350

[Feedman]

Adam, if you need another option, you can call my brother in law who is a paint and body specialist.
He's really good.

SE Customs 984-0350

Little advertising...lol....I might do that too.... 8)

[ben2000formula]

Does your brother go as far doing body work to cut about a 2 inch section out of a rear quarter panel and weld new metal in it's place to stop rust? i have been looking for some one to do that because my hatch has a very tiny spot of rust on, other then that it is rust free.

[Davis Silver Sti]

Does your brother go as far doing body work to cut about a 2 inch section out of a rear quarter panel and weld new metal in it's place to stop rust? i have been looking for some one to do that because my hatch has a very tiny spot of rust on, other then that it is rust free.

Yes...he is currently renovating an old Ford truck, Studebaker, finsihed an old Model-T looking car as well as other customer cars.

He'll post on here little later. I just got on his case for being a stranger on movfast:)

[Feedman]

Does your brother go as far doing body work to cut about a 2 inch section out of a rear quarter panel and weld new metal in it's place to stop rust? i have been looking for some one to do that because my hatch has a very tiny spot of rust on, other then that it is rust free.



We could cut it out, cut some sheet metal, weld it back in place and grind it down, ready for paint....

That was the plan on Justins crx if he keeps it.... 8)

[Feedman]

Adam, if you need another option, you can call my brother in law who is a paint and body specialist.
He's really good.

SE Customs 984-0350

I called him. Seems like a nice guy. He said it would take only a couple of days.

Ballpark would be around $200 bucks...

8)

[narfdanarf]

Does your brother go as far doing body work to cut about a 2 inch section out of a rear quarter panel and weld new metal in it's place to stop rust? i have been looking for some one to do that because my hatch has a very tiny spot of rust on, other then that it is rust free.



We could cut it out, cut some sheet metal, weld it back in place and grind it down, ready for paint....

That was the plan on Justins crx if he keeps it.... 8)

there really isn't any rust on my CRX except the passenger fender, which i'm just going to go ahead and replace :D

[Don juan futon]

Does your brother go as far doing body work to cut about a 2 inch section out of a rear quarter panel and weld new metal in it's place to stop rust? i have been looking for some one to do that because my hatch has a very tiny spot of rust on, other then that it is rust free.

Yes...he is currently renovating an old Ford truck, Studebaker, finsihed an old Model-T looking car as well as other customer cars.

He'll post on here little later. I just got on his case for being a stranger on movfast:)

We could use a good body man on here.

[ben2000formula]

That would be awesome if he could do that! He would just need to name his price and i would be there!

[daveb91]

I am disapointed Adam when I was asking about getting my car painted you told me to do it myself and that it was easy. So are you being a hippocrite or just cute.

[Feedman]

I am disapointed Adam when I was asking about getting my car painted you told me to do it myself and that it was easy. So are you being a hippocrite or just cute.

Well I think I am gonna prep it, and have him spray it, b/c I don't have a compressor or paint gun yet...

8)

[daveb91]

hey i did all my own prep work and all they had to do was spray it. Cheaper that way by far.

[Feedman]

hey i did all my own prep work and all they had to do was spray it. Cheaper that way by far.

Agree...save me some cash...

This has paint on it, I need to clean all that off, whats the best way...?

Thanks.... 8)

[SE Customs]

Use 320 grit and featheredge all of the chips and flakes off of it, and then if you are going to do it use k36 as a primer surfacer and then sand it smooth with 400-600 wet. It makes a nice smooth finish. And yes i can do all metal work and shapeing. My buddy just got an english wheel and a planishing hammer so there isnt much we cant do with metal now.

[Feedman]

Use 320 grit and featheredge all of the chips and flakes off of it, and then if you are going to do it use k36 as a primer surfacer and then sand it smooth with 400-600 wet. It makes a nice smooth finish. And yes i can do all metal work and shapeing. My buddy just got an english wheel and a planishing hammer so there isnt much we cant do with metal now.

Thanks, I am going to sand it down and have you spray I do beleive..... 8)

[SE Customs]

that sounds fine, just get ahold of me so i can schedule you in, im getting kinda busy so just call. Do you remember the number?

[Feedman]

that sounds fine, just get ahold of me so i can schedule you in, im getting kinda busy so just call. Do you remember the number?

Thanks man.

I am going to prep it myself, so I can save some cash.

I will be in touch.

8)

[Feedman]

Justed talked to him on the phone.

Great guy.

I am gonna try and get some sandpaper ASAP and get it taken care of.

8)

[clintsGSRcrx]

hey i would like to find a price on cutting my rust out on my rear quater panal. i want to find someone that can do a good job.